Free Shipping* & Free Lock Picking Guide

Best Lockout Tools for a Door Lockout Kit: Fast, Damage-Free Entry for First Responders

Dangerfield J-Tool reach-through tool for turning the inside thumbturn on commercial double doors

Chris Dangerfield

A locked door on a callout is rarely a lock picking problem. It's a time problem. Someone has fallen behind a front door, a resident has locked themselves out with the oven on, or a welfare check lands on a door nobody is answering. Your crew wants in fast, and the homeowner wants a door that still closes behind you.

After twenty years of opening locks, my advice to any fire, EMS, police or facilities team is simple: build your lockout kit around the door first and the lock second. Most doors give you a faster way in than the cylinder, and the right flat tool in the bag turns a ten-minute job into a thirty-second one.

Here are the best lockout tools to carry, the order we'd reach for each one, and three ready-made door lockout kits by budget.

Dangerfield J-Tool reach-through tool for turning the inside thumbturn on commercial double doors
The Dangerfield J-Tool reaches between double doors and turns the thumbturn on the inside. No drilling, no broken glass.

Read the door before you reach for a pick

Take ten seconds at the door. Which way does it open? Is the latch a sloped spring latch, or has a deadbolt been thrown? Is there a thumbturn on the inside of a double door? Is there a gap at the frame? Those four answers tell you which tool comes out of the bag first.

The order we recommend, fastest first: slip the latch, reach the handle or thumbturn, then pick or decode the cylinder. Pull the cylinder plug only when nothing else will move, because that's the one step that costs the owner a new cylinder.

Step 1: Slip the spring latch

A huge number of interior doors, apartment doors and office doors close on a sloped spring latch with nothing else holding them. Slip that latch and the door swings open with no marks at all.

A set of mica latch shims is the tool for this. Mica is thin and springy, so a shim slides into the gap between the door and the frame, finds the sloped face of the latch and presses it back into the door. The five shims in the set give you different stiffness and reach, which matters because frames, weatherstrip and gaps vary from door to door.

If the door has a dead latch (the small plunger beside the main bolt) or the deadbolt is thrown, the latch is held. Move straight to Step 2.

Step 2: Reach the handle or the thumbturn

When the latch is held, the inside hardware is often the weak point. Two slim tools cover the doors you'll meet most:

  • Outward-opening doors with lever handles: the Dangerfield Universal Latch Bypass Tool, also called a traveler hook or Shrum tool, feeds through the gap near the latch, catches the inside lever and pulls it down so the door opens towards you.
  • Commercial double doors with an inside thumbturn: the Dangerfield J-Tool slips through the gap between the two doors, hooks around to the inside and turns the thumbturn to draw the bolt. No drilling, no broken glass, no damaged hardware.

A pair of wedges makes both tools easier. The KLOM nylon wedge holds a gap open steadily while you work, and the KLOM lever wedge gives you a controlled spread when the gap starts out too tight for the tool.

Step 3: Pick or decode the cylinder

When the deadbolt is thrown and there's no way to the inside hardware, you're on the lock itself. Two tools earn a place in a callout bag here.

Lishi 2-in-1 picks for the locks on American homes. Most front doors in the US run a Kwikset or Schlage cylinder. A Lishi tool is cut for one keyway, so it slides in with the right shape, lets you set each pin one at a time, and then reads the cut depths so you know the key once the door is open. The Lishi Residential Small Pack covers Kwikset KW1, Kwikset KW5 and Schlage SC1 in one order. If you're not sure which lock is which, our guide to keyways shows you how to spot each one at the door.

An electric pick gun for speed on pin tumbler locks. An EPG drives a needle that kicks every pin at once while you hold light tension, and on a lot of standard cylinders it opens in seconds. The KLOM Electric Pick Gun PLUS comes in a hard case with a US charger, and a pack of 0.024 inch spare needles keeps it working when a needle bends on a stubborn lock. Tension still decides whether it opens, so give your team bench time with it before it rides on the truck.

Step 4: When nothing else moves

Snapped key in the lock. If someone has broken a key off in the cylinder, a broken key extractor set slides in beside the fragment, bites the cuts and draws it back out. The lock works again and you've saved the owner a locksmith bill.

Pull the plug. When time matters more than the cylinder, the Lokko Bell Plug Puller Set bites a self-tapping screw into the plug, seats the bell over the lock face and draws the plug straight out. You turn the cam and the door opens. The cylinder needs replacing afterwards, but the door, frame and glass stay untouched, which beats a halligan through the frame every time.

Cars and vehicles

Vehicle lockouts work on the same principle: make a small, controlled gap, then reach or pick. The KLOM wedges above double as car-entry wedges for holding a door gap open. On older vehicles with wafer locks, the Mini, Medium and Auto Jigglers set gives you a range of profiles to work the lock. For two of the keyways you'll meet often, carry the Ford HU101 inner groove pick and the Mercedes Benz inner groove pick. The rest of our vehicle tools are together in our car lockout kits.

Car Lishi tools take it a step further. Like the house Lishi picks above, each one is cut for a single car keyway, so you pick the door lock pin by pin or wafer by wafer and then read the cut depths off the decoder. The car opens without a mark, and you leave knowing the key code, which turns a lockout into a lost-key job a locksmith can cut for. Our Lishi range covers GM, Chrysler, Hyundai and Kia keyways among others, so match the keyway first and the tool does the rest.

Lockout tools by door: quick reference

Door or job First tool Back-up
Spring latch, no deadbolt Mica latch shims Universal latch bypass tool
Outward-opening door, lever handle Universal latch bypass tool Nylon wedge to hold the gap
Double doors, inside thumbturn J-Tool Lever wedge to open the gap
Kwikset or Schlage deadbolt thrown Lishi KW1, KW5 or SC1 Electric pick gun
Other pin tumbler cylinder Electric pick gun Bell plug puller
Key snapped in the lock Broken key extractor set Bell plug puller
Car with a wafer lock Auto jigglers Ford or Mercedes inner groove pick

Three lockout kits by budget

Every department has a different budget line, so here are three kits we'd put together, each one building on the last.

Pocket bypass roll

Under $50

The latch tools that open the most doors for the least money. Fits in a turnout pocket or a glovebox.

  • Universal latch bypass tool
  • Mica latch shims (5)
  • KLOM nylon wedge

Door entry bag

Under $250

Everything in the pocket roll, plus the tools for thrown deadbolts on Kwikset and Schlage doors.

  • Pocket bypass roll
  • J-Tool for thumbturn doors
  • KLOM lever wedge
  • Lishi Residential Small Pack (KW1, KW5, SC1)
  • Broken key extractor set

Full callout kit

Under $500

The door entry bag, plus speed on any pin tumbler cylinder and a way through when nothing else moves.

  • Door entry bag
  • KLOM Electric Pick Gun PLUS
  • 0.024 inch spare needles (10)
  • Lokko Bell Plug Puller Set

Kitting out a whole station or several rigs? Email hello@lockpickworld.com with the kit and the number of crews, and we'll put together a department quote.

Train on the bench, not on the callout

Every tool here gets faster with a few practice sessions. Fit a spare lock to a board, give each crew member ten minutes with the mica shims and the Lishi, and the first real callout feels familiar. A set of clear practice locks lets your team see the pins move while they learn the feel, and the Beginners Visual Guide walks anyone new to it through tension, pin setting and picking with 200+ color illustrations.

Lockout kit questions

What should a first responder lockout kit include?

Start with latch tools (mica latch shims), add reach tools for lever handles and thumbturns (a latch bypass tool and a J-Tool), carry two wedges, then add cylinder tools for thrown deadbolts: Lishi picks for Kwikset and Schlage, and an electric pick gun. A broken key extractor and a bell plug puller cover the rest.

What's the fastest way through a locked door without damage?

On a door held only by a spring latch, a mica shim usually opens it in seconds. On a thrown deadbolt, go for the inside thumbturn with a J-Tool if the doors allow it, then the cylinder with a Lishi or an electric pick gun.

Is a bell plug puller damage-free?

It saves the door, frame and glass, and it costs one cylinder. Use it when time matters more than the lock, and fit a new cylinder afterwards.

Can you supply kits for a whole department?

Yes. Email hello@lockpickworld.com with the kit you want and how many crews need one, and we'll send a quote.